Choose your delivery country to see correct prices, VAT and shippingSee prices for your country Choose country
Menu toggle

Welcome

A6070700301: Fuel pump for Renault CLIO IV (BH_)

A6070700301: Fuel pump for Renault CLIO IV (BH_)

  • Original Number (OEM): 0445010530, 0445010704, 167007358R, 167001056R, H8201434847, 191008, A6070700301, A6070700101, 0445010563
  • Article Number: N_0613_378026
  • Brand: Renault
  • VIN-number: VF15RJL0H53149699
  • km: 226.223
  • Year: 2015
  • See more specifications

217,43 EUR

Add to basket

Estimated shippingtime 3-6 days

Express delivery can be purchased
See all 2 parts with OEM A6070700301

What is OEM number A6070700301 and which part does it identify?

OEM number A6070700301 identifies the high-pressure fuel pump for the Renault Kangoo Express, second generation (model code FW0/1_), covering the 2010–2026 production period. The part applies specifically to the 1.5 dCi 75 diesel variant, equipped with a 1,461 cc four-cylinder engine producing 55 kW (75 hp), and is matched to engine codes K9K 608, K9K 628, and K9K 808. The high-pressure fuel pump is also referred to as the injection pump or high-pressure injection pump — all three terms describe the same component. The Mercedes-Benz OEM part number series A 607 070 is shared with equivalent Renault applications because the 1.5 dCi (K9K) engine is used under licence across both brands' commercial vehicle ranges. OEM number A6070700301 may fit additional vehicle models not listed here — always verify against the OEM number on your existing part or with a VIN-based lookup.


Does OEM number A6070700301 fit my vehicle?

OEM number A6070700301 fits the Renault Kangoo Express second generation (FW0/1_), built between 2010 and 2026, in the 1.5 dCi 75 specification. Fitment is governed by engine code: only vehicles carrying engine codes K9K 608, K9K 628, or K9K 808 are confirmed applications. All body types within the Kangoo Express FW0/1_ range are covered; there is no drive-layout restriction, as this variant is front-wheel drive only.

The critical constraint is engine code. The K9K family encompasses a wide range of power outputs and injection system configurations across many vehicle lines; the A6070700301 high-pressure fuel pump is confirmed only for the 55 kW / 75 hp output variants listed. Kangoo Express variants with higher-output K9K derivatives (such as the 1.5 dCi 90 or 1.5 dCi 110) use a differently rated high-pressure pump and must be verified separately before ordering. Variants equipped with a Siemens/Continental injection system rather than the Delphi system are not compatible.

Make Model Body / variant Year range Engine code
Renault Kangoo Express (FW0/1_) Estate / van — 1.5 dCi 75 2010–2026 K9K 608
Renault Kangoo Express (FW0/1_) Estate / van — 1.5 dCi 75 2010–2026 K9K 628
Renault Kangoo Express (FW0/1_) Estate / van — 1.5 dCi 75 2010–2026 K9K 808

Cross-reference data also associates the broader A 607 070 OEM number series with select Mercedes-Benz commercial van applications sharing the 1.5 dCi (K9K) platform, but the specific suffix variant A6070700301 has not been independently confirmed for those applications — verify the printed number on your existing part before ordering.

OEM number A6070700301 may fit additional vehicle models not listed here. Always verify by checking the OEM number printed on your existing part or by using a VIN-based parts lookup.

Fits:     Renault Kangoo Express (FW0/1_), 1.5 dCi 75, engine codes K9K 608 / K9K 628 / K9K 808, 2010–2026, front-wheel drive, Delphi injection system
Does not fit: K9K variants other than 55 kW / 75 hp; vehicles with Siemens/Continental injection system

How is OEM number A6070700301 installed?

The high-pressure fuel pump is a precision hydraulic component driven directly off the camshaft or auxiliary shaft and integrated into the diesel common-rail injection circuit. Installation requires more than a straightforward bolt-on exchange.

Fuel system depressurisation and contamination control. The common-rail system on K9K engines operates at pressures up to 1,600 bar. The high-pressure circuit must be fully depressurised before disconnecting any union. All open unions must be capped immediately using a dedicated K9K blanking plug set (Delphi/Renault tool reference) to prevent debris ingress. Any contamination of the injection circuit can damage injectors and the fuel rail.

Timing and drive alignment. The high-pressure pump is driven by the auxiliary belt or timing belt circuit depending on the model year. Confirm the correct drive arrangement for the specific vehicle before removal. Where the pump is belt-driven from the timing belt, the engine must be locked at top dead centre (TDC) before removal to preserve valve timing.

Post-installation procedure:

  1. Prime the low-pressure circuit by cycling the ignition three to four times (without cranking) to allow the low-pressure transfer pump to fill the high-pressure pump.
  2. Inspect all fuel union connections for leaks with the engine at idle before raising engine speed.
  3. Clear any stored fault codes using a compatible diagnostic tool (e.g. a Renault-compatible scanner such as CLIP or equivalent OBD-II tool) and monitor fuel rail pressure live data to confirm the pump achieves target pressure.
  4. Check for fuel leaks at the pump inlet union, outlet union, and camshaft seal after the first warm-up cycle.
  5. Road-test and confirm smooth fuelling, absence of hard starting, and no illuminated warning lights.

Battery disconnection. Disconnect the negative battery terminal before beginning work to prevent inadvertent injection system activation.


When should OEM number A6070700301 be replaced?

Replacement triggers

  • Hard starting or extended cranking before the engine fires, particularly when the engine is cold.
  • Rough idle with irregular combustion, especially under light load.
  • Loss of power under acceleration, often accompanied by the engine entering limp-home mode.
  • Engine management warning light illuminated, with diagnostic fault codes indicating low rail pressure (e.g. P0087 — fuel rail pressure too low).
  • Audible knocking or rattling from the pump at low engine speed, distinct from normal injector noise.
  • Fuel contamination of the engine oil (diesel dilution), which may indicate pump seal failure allowing fuel to enter the lubrication circuit.
  • Visible fuel leak at the high-pressure pump body, inlet union, or outlet union.

Typical lifespan

The high-pressure fuel pump on the K9K 1.5 dCi engine typically lasts 150,000–200,000 km under normal operating conditions, although premature wear before 100,000 km is documented on these engines, particularly where fuel quality has been poor or oil change intervals have been extended. Low-quality or contaminated diesel accelerates internal wear of the pump's precision metering components, as the fuel itself provides lubrication to the pump's internal surfaces. Regular fuel filter replacement at the manufacturer-specified interval is the single most effective preventative measure.

We used AI to help write this text. We regularly check the information - but cannot guarantee that all data is accurate.

Which delivery type should I choose?

shipping iconExpress delivery

If time is of the essence – and when you want your part delivered quickly to your address. Best when you want your second-hand part sent directly to your address and when you need a very speedy delivery. Choosing express delivery gets your second-hand part to you within 1-2 business days.

shipping iconStandard delivery

If you want the item delivered to your address. Best when you want your part sent directly to your address. Choosing standard delivery gets your part to you within 3-5 business days.

See all A6070700301 parts for sale

See all A6070700301 parts for sale

OEM number A6070700301 belongs to the following type of sparepart(s): Fuel pump. We currently have 2 pieces for sale. These fit RENAULT and MERCEDES-BENZ

The prices shown are excluding VAT and including freight costs to United Kingdom. The price you see is the price you pay.